在济南标识制作中，有时候会发生这么有一种问题：打印空白处的无规则拉丝体现为时有时无、时长时短的无规律墨道，一般比较粗。下面是针对这个问题总结的产生缘由剖析和处理方法：
In the Ji'nan logo production, and sometimes there will be a problem: the printing blank of the irregular wire drawing is sometimes not, when the long short irregular ink Road, generally relatively coarse. The following is a summary of the problems of the causes of the analysis and processing methods:
1、刮墨刀刃口或刀下面粘有异物能够在印刷停止过程中前后、上下挪动刮墨刀，摆掉粘着的异物或用一根竹签直接在刮墨刀刃上剔除(必需由纯熟操作工完成，以免因操作不当形成不用要的损失)，必要时需停机对刮墨刀停止彻底清算。
1, scraping knife blade or stuck under the foreign body in the printing process, and can stop in the next move of scraping knife, put off the adhesive or foreign body with a bamboo stick directly in the scraping blade (excluding must complete by skilled operators, in order to avoid improper operation of unnecessary loss, necessary) when you need to stop up completely to stop scraping knife.
2、油墨循环不行有些油墨在墨槽内的死角位置，因得不到杰出循环而构成树脂分出，构成巨细不一样的结晶与结块，或过火枯燥构成外表构成墨皮(夏天简单发生墨皮，春秋两季由于气温的影响油墨结晶和结块的状况较多)，跟着油墨的循环，有一有些油墨结晶或墨皮被转动的版滚筒带到刀刃处，刮墨刀将其打碎而构成无规则拉丝。所以有必要从油墨的循环和过滤两方面进行改善。
2, not some ink in the ink ink circulation groove of the corner position, due to outstanding circulation formed resin separation, crystallization and agglomeration of the same size, or too boring which formed on the surface of skin (summer simple occurrence of ink skin, spring and autumn season two due to the temperature effects of ink crystallization and agglomeration situation more) follow, the ink circulation, there is a version of the drum is rotated or some ink crystallization skin brought to the blade, scraping knife the broken and irregular form drawing. So it is necessary to improve from the two aspects of the cycle of ink and filtration.
(1)循环改善。济南标识制作办法一，将墨槽摆布歪斜，确保油墨能够由稍高的一端写入，从较低的一端流出，构成杰出的循环;济南标识制作办法二，将墨槽平放，但油墨有必要从两端一起写入，从中心回流，这么也可构成极好的循环，不可从单边写入油墨。
(1) cycle improvement. The method of making a mark in Ji'nan, will be at the mercy of the ink tank to ensure ink skew, written by the end of the slightly higher, the outflow from the lower end, to form a good circulation; Ji'nan logo production to two, the ink tank is flat, but the ink is necessary from both ends to the center, from the back, so also can form excellent the cycle, not from unilateral write ink.
(2)过滤改良。油墨运用前必需停止初次过滤，即便是新墨也要过滤，普通运用140目/英寸的过滤网。油墨在墨槽中循环的过滤工作愈加重要，它能够很好地过滤掉油墨在运用过程中构成的树脂结晶和外来杂质，选择的网目应更细，办法是在出墨斗的下方套一丝袜，构成一过滤套斗，在过滤一段时间后，假如过滤网被堵，流墨不畅，能够在套斗的上方用竹签插一些小洞，增加导墨效果，套斗的下方还能够起到很好的堆积杂质的作用。
(2) filtration and improvement. Prior to the use of ink must stop the initial filter, even if the new ink also want to filter, the general use of 140 mesh / inch filter. The ink in the ink tank circulation filtering work becomes more and more important, it can filter out a good crystalline resin ink in the course of the formation and the extraneous material selection should be more fine mesh, in a way is the fountain below a silk stockings, a set of filter in the filter bucket, after a period of time, if the filter is blocked, the ink flow is not smooth, can be inserted in small holes in the top set with bamboo bucket, increase the ink guiding effect, set below the bucket can also play a very good role in the accumulation of impurities.
3、油墨疲惫此种状况多发生在印版着墨面积比较小时。打印过程中，油墨中的树脂不断被消耗，假如接连参加溶剂而不增加新墨，树脂得不到弥补，使油墨各成分的份额发生变化，然后构成油墨疲惫并影响正常运用。恰当增加新墨即可解决问题。
3, tired of this situation occurred in the ink printing ink area is small. In the process of printing, ink resin in the continuous consumption, if successive in solvent rather than adding new ink, resin not to make up, so that the ink components share changes, then tired and affect the normal use of ink. Appropriate to increase the new ink to solve the problem.